Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairMaytag Dryer Terminal Block Replacement #Y304596
Maytag Dryer Terminal Block Replacement #Y304596
Skill Level
Total Parts Cost
$29.50Estimated Savings
$112.5003:14
- Description
This video provides step-by-step instructions for replacing the terminal block on Maytag and Kenmore dryers. The most common reason for replacing the terminal block is when the dryer trips the breaker.
All of the information in this terminal block replacement video is applicable to the following brands: Maytag, Whirlpool
Tools needed: screwdriver, wrench
All of the information in this terminal block replacement video is applicable to the following brands: Maytag, Whirlpool
Tools needed: screwdriver, wrench
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the bottom of the front panel.
3
Now, rotate the panel out from the bottom to release the clips at the top.
4
Noting their location, disconnect the wires from the door switch as well as from the retaining clip on the panel and set the panel aside.
5
Release the wires from the front bulkhead.
6
Remove the screws to release the heating element shield.
7
Remove the nut to disconnect the power supply wire.
8
Now remove the nut and washer to release the heating element coil.
9
Remove the nut to detach the old insulators and post.
10
Install the new insulators by sliding the male insulator onto the post then insert into the heating element housing.
11
Slide the female insulator onto the post and secure with the nut.
12
Be careful not to over-tighten.
13
Replace the heating element coil and secure with the washer and nut.
14
Reattach the power supply wire and secure with the nut.
15
Replace the heating element shield and secure with the screws.
16
Secure the door switch wires on the retaining clips of both the bulkhead and the front panel then reconnect the wires to the door switch.
17
Position the front panel clips under the lip of the main top and rotate the panel into place.
18
Secure it with the mounting screws.
19
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Description
This video provides step-by-step instructions for replacing the terminal block on Maytag and Kenmore dryers. The most common reason for replacing the terminal block is when the dryer trips the breaker.
All of the information in this terminal block replacement video is applicable to the following brands: Maytag, Whirlpool
Tools needed: screwdriver, wrench
All of the information in this terminal block replacement video is applicable to the following brands: Maytag, Whirlpool
Tools needed: screwdriver, wrench
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the screws at the bottom of the front panel.
3
Now, rotate the panel out from the bottom to release the clips at the top.
4
Noting their location, disconnect the wires from the door switch as well as from the retaining clip on the panel and set the panel aside.
5
Release the wires from the front bulkhead.
6
Remove the screws to release the heating element shield.
7
Remove the nut to disconnect the power supply wire.
8
Now remove the nut and washer to release the heating element coil.
9
Remove the nut to detach the old insulators and post.
10
Install the new insulators by sliding the male insulator onto the post then insert into the heating element housing.
11
Slide the female insulator onto the post and secure with the nut.
12
Be careful not to over-tighten.
13
Replace the heating element coil and secure with the washer and nut.
14
Reattach the power supply wire and secure with the nut.
15
Replace the heating element shield and secure with the screws.
16
Secure the door switch wires on the retaining clips of both the bulkhead and the front panel then reconnect the wires to the door switch.
17
Position the front panel clips under the lip of the main top and rotate the panel into place.
18
Secure it with the mounting screws.
19
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Applicable Product Model
Parts Needed
Ceramic Receptacle Block
$29.50
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com