Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Electric Washer/Dryer Combo Control Panel Replacement #W10696103 
Whirlpool Electric Washer/Dryer Combo Control Panel Replacement #W10696103
Skill Level
Total Parts Cost
$177.87Estimated Savings
$112.5004:01
- Description
This video provides step-by-step repair instructions for replacing the control panel on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if it is damaged or missing.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Before you replace the control panel on your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a 5/16th inch socket or nut driver to unthread the three screws securing the control panel assembly.
4
Detach the panel assembly.
5
Make sure the washer timer knob is pushed in.
6
Now use a small flat-head screwdriver to pry out the retaining pin so you can remove the knob.
7
Next, pull the timer dial forward to detach.
8
Pull off the remaining control knobs.
9
Unthread the screw located under the timer dial.
10
Release the clips from the front panel and set the control panel assembly on the top of the appliance.
11
Unthread the screws securing the left and right end caps to the control panel.
12
Detach the end caps.
13
Remove the mounting clips and set them aside.
14
You can now remove the old panel.
15
Before you install the new control panel…
16
…peel off the protective coating.
17
Now position the new panel on the mounting plate.
18
Reposition the mounting clips.
19
Fully align the panel and mounting plate.
20
Reinstall the end caps.
21
Thread the screws to secure.
22
Now reinsert the mounting clips into the slots in the front panel.
23
Realign the knobs on the switch stems.
24
thread the front screw.
25
Reinstall the timer dial by aligning it on the shaft until it is flush against the control panel.
26
Replace the timer knob.
27
Now push the retaining pin in to secure.
28
Realign the control panel assembly.
29
Rethread the three screws on top.
30
Plug the power cord back in or restore the power supply…
31
…and your washer/dryer combo should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the control panel on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if it is damaged or missing.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Before you replace the control panel on your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a 5/16th inch socket or nut driver to unthread the three screws securing the control panel assembly.
4
Detach the panel assembly.
5
Make sure the washer timer knob is pushed in.
6
Now use a small flat-head screwdriver to pry out the retaining pin so you can remove the knob.
7
Next, pull the timer dial forward to detach.
8
Pull off the remaining control knobs.
9
Unthread the screw located under the timer dial.
10
Release the clips from the front panel and set the control panel assembly on the top of the appliance.
11
Unthread the screws securing the left and right end caps to the control panel.
12
Detach the end caps.
13
Remove the mounting clips and set them aside.
14
You can now remove the old panel.
15
Before you install the new control panel…
16
…peel off the protective coating.
17
Now position the new panel on the mounting plate.
18
Reposition the mounting clips.
19
Fully align the panel and mounting plate.
20
Reinstall the end caps.
21
Thread the screws to secure.
22
Now reinsert the mounting clips into the slots in the front panel.
23
Realign the knobs on the switch stems.
24
thread the front screw.
25
Reinstall the timer dial by aligning it on the shaft until it is flush against the control panel.
26
Replace the timer knob.
27
Now push the retaining pin in to secure.
28
Realign the control panel assembly.
29
Rethread the three screws on top.
30
Plug the power cord back in or restore the power supply…
31
…and your washer/dryer combo should be ready for use.
Applicable Product Model
Parts Needed
Control Panel
$177.87
Total$0.00
Related Articles & Videos
05:07
Part Replacement
Whirlpool Electric Washer/Dryer Combo Lid Switch Assembly Replacement Part # WP3355458
08:48
Part Replacement
Whirlpool Electric Washer/Dryer Combo Dryer Drive Belt Replacement #661570V
04:26
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Thermal Fuse Replacement #279769
05:56
Part Replacement
Whirlpool Electric Washer/Dryer Combo Water Inlet Valve Replacement #W10919200
03:57
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Replacement #WP3387749
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com