Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Electric Washer/Dryer Combo Washer Timer Replacement #WPW10113804 
Whirlpool Electric Washer/Dryer Combo Washer Timer Replacement #WPW10113804
Skill Level
Total Parts Cost
$194.81Estimated Savings
$112.5002:56
- Description
This video provides step-by-step repair instructions for replacing the washer timer on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if the washer will not start.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Before you replace the washer timer in your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a 5/16th inch socket or nut driver to unthread the three screws securing the control panel assembly.
4
Detach the panel assembly.
5
Make sure the washer timer knob is pushed in.
6
Now use a small flat-head screwdriver to pry out the retaining pin so you can remove the knob.
7
Next, pull the timer dial forward to detach.
8
Use a quarter-inch socket or nut driver to unthread the front screw securing the timer.
9
Lift the water temperature switch arm up and rotate the switch so you can fully access the rear screw securing the timer.
10
Slide the timer to the right to detach.
11
Lift up the tab to disconnect the wire connecter.
12
Install the new washer timer…
13
…by first connecting the wire connecter.
14
Now insert the tabs into the slots in the control panel assembly and slide the timer to the left.
15
Thread the rear screw.
16
Fully reposition the water temperature switch.
17
Thread the front screw.
18
Reinstall the timer dial by aligning it on the shaft until it is flush against the control panel.
19
Replace the timer knob.
20
Now push the retaining pin in to secure.
21
Realign the control panel assembly.
22
Rethread the three screws on top.
23
Plug the power cord back in or restore the power supply…
24
…and your washer/dryer combo should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the washer timer on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if the washer will not start.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Before you replace the washer timer in your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a 5/16th inch socket or nut driver to unthread the three screws securing the control panel assembly.
4
Detach the panel assembly.
5
Make sure the washer timer knob is pushed in.
6
Now use a small flat-head screwdriver to pry out the retaining pin so you can remove the knob.
7
Next, pull the timer dial forward to detach.
8
Use a quarter-inch socket or nut driver to unthread the front screw securing the timer.
9
Lift the water temperature switch arm up and rotate the switch so you can fully access the rear screw securing the timer.
10
Slide the timer to the right to detach.
11
Lift up the tab to disconnect the wire connecter.
12
Install the new washer timer…
13
…by first connecting the wire connecter.
14
Now insert the tabs into the slots in the control panel assembly and slide the timer to the left.
15
Thread the rear screw.
16
Fully reposition the water temperature switch.
17
Thread the front screw.
18
Reinstall the timer dial by aligning it on the shaft until it is flush against the control panel.
19
Replace the timer knob.
20
Now push the retaining pin in to secure.
21
Realign the control panel assembly.
22
Rethread the three screws on top.
23
Plug the power cord back in or restore the power supply…
24
…and your washer/dryer combo should be ready for use.
Applicable Product Model
Parts Needed
Timer
$194.81
Total$0.00
Related Articles & Videos
05:07
Part Replacement
Whirlpool Electric Washer/Dryer Combo Lid Switch Assembly Replacement Part # WP3355458
08:48
Part Replacement
Whirlpool Electric Washer/Dryer Combo Dryer Drive Belt Replacement #661570V
04:26
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Thermal Fuse Replacement #279769
05:56
Part Replacement
Whirlpool Electric Washer/Dryer Combo Water Inlet Valve Replacement #W10919200
03:57
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Replacement #WP3387749
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com