Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Electric Washer/Dryer Combo Water Inlet Spout Hose Replacement #8521954 
Whirlpool Electric Washer/Dryer Combo Water Inlet Spout Hose Replacement #8521954
Skill Level
Total Parts Cost
$44.49Estimated Savings
$112.5005:42
- Description
This video provides step-by-step repair instructions for replacing the water inlet spout hose on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if the washer is not filling.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Before you replace the water inlet spout hose in your washer / dryer combo…
2
…you will need to pull the appliance away from the wall to access the rear.
3
Unplug the power cord or shut off the power supply…
4
Shut off the water supply as well.
5
Note the orientation of the hot and cold water supply lines…then detach them from the inlet valve ports – be prepared for some water to spill.
6
Use a phillips-head screwdriver to unthread the screws securing the lower access panel.
7
Detach the panel and set it aside.
8
Remove the two rear access panel clips
9
Use a quarter-inch socket or nut driver to unthread the screws so you can detach the access panels.
10
Use a short flat-head screwdriver to help detach the spring clips securing the washer’s top panel and lid.
11
Pull the top panel forward then lift up.
12
Use a 5/16th inch socket or wrench to loosen the water inlet valve plate mounting screw so you can detach the assembly.
13
Use pliers to release the spring clamp to detach the spout hose from the valve.
14
Release the clamp securing the hose to the inlet spout and you can fully remove the old hose.
15
Prepare the new water inlet spout hose for installation…
16
…by transferring the two spring clamps from the old hose to the new one.
17
Now attach the long end of the hose to the inlet spout and secure with the clamp.
18
Attach the opposite end to the inlet valve and secure with the clamp.
19
Align the mounting plate tab on the outside of the rear panel…fully reposition the plate…
20
…then tighten the mounting screw.
21
Realign the top panel and lid on the washer and push the panel straight back.
22
Be aware the lid switch wire connecter on the panel needs to be fully connected with the receptacle on the frame.
23
Reinsert the two spring clips to secure the panel.
24
Reposition the rear access panels and rethread the screws.
25
Reinsert the access panel clips.
26
Reposition the lower access panel and secure it with the screws.
27
Attach the hot and cold water supply lines to the appropriate valve ports.
28
Turn the water supply back on…
29
…plug the power cord back in or restore the power supply…
30
…and your washer/dryer combo should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the water inlet spout hose on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if the washer is not filling.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Before you replace the water inlet spout hose in your washer / dryer combo…
2
…you will need to pull the appliance away from the wall to access the rear.
3
Unplug the power cord or shut off the power supply…
4
Shut off the water supply as well.
5
Note the orientation of the hot and cold water supply lines…then detach them from the inlet valve ports – be prepared for some water to spill.
6
Use a phillips-head screwdriver to unthread the screws securing the lower access panel.
7
Detach the panel and set it aside.
8
Remove the two rear access panel clips
9
Use a quarter-inch socket or nut driver to unthread the screws so you can detach the access panels.
10
Use a short flat-head screwdriver to help detach the spring clips securing the washer’s top panel and lid.
11
Pull the top panel forward then lift up.
12
Use a 5/16th inch socket or wrench to loosen the water inlet valve plate mounting screw so you can detach the assembly.
13
Use pliers to release the spring clamp to detach the spout hose from the valve.
14
Release the clamp securing the hose to the inlet spout and you can fully remove the old hose.
15
Prepare the new water inlet spout hose for installation…
16
…by transferring the two spring clamps from the old hose to the new one.
17
Now attach the long end of the hose to the inlet spout and secure with the clamp.
18
Attach the opposite end to the inlet valve and secure with the clamp.
19
Align the mounting plate tab on the outside of the rear panel…fully reposition the plate…
20
…then tighten the mounting screw.
21
Realign the top panel and lid on the washer and push the panel straight back.
22
Be aware the lid switch wire connecter on the panel needs to be fully connected with the receptacle on the frame.
23
Reinsert the two spring clips to secure the panel.
24
Reposition the rear access panels and rethread the screws.
25
Reinsert the access panel clips.
26
Reposition the lower access panel and secure it with the screws.
27
Attach the hot and cold water supply lines to the appropriate valve ports.
28
Turn the water supply back on…
29
…plug the power cord back in or restore the power supply…
30
…and your washer/dryer combo should be ready for use.
Applicable Product Model
Related Articles & Videos
05:07
Part Replacement
Whirlpool Electric Washer/Dryer Combo Lid Switch Assembly Replacement Part # WP3355458
08:48
Part Replacement
Whirlpool Electric Washer/Dryer Combo Dryer Drive Belt Replacement #661570V
04:26
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Thermal Fuse Replacement #279769
05:56
Part Replacement
Whirlpool Electric Washer/Dryer Combo Water Inlet Valve Replacement #W10919200
03:57
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Replacement #WP3387749
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com