Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Electric Washer/Dryer Combo Tub-to-Pump Hose Replacement #285871 
Whirlpool Electric Washer/Dryer Combo Tub-to-Pump Hose Replacement #285871
Skill Level
Total Parts Cost
$22.20Estimated Savings
$112.5005:13
- Description
This video provides step-by-step repair instructions for replacing the tub-to-pump hose on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if the washer is not draining.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Before you replace the tub-to-pump hose in your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a phillips-head screwdriver to unthread the screws securing the lower access panel.
4
Detach the panel and set it aside.
5
Remove the two rear access panel clips
6
Use a quarter-inch socket or nut driver to unthread the screws so you can detach the access panels.
7
Use a short flat-head screwdriver to help detach the spring clips securing the washer’s top panel and lid.
8
Pull the top panel forward then lift up.
9
Use a 5/16th inch socket or nut driver to unthread the screw to release the support bar from the front panel.
10
Next, unthread the screws securing the front panel to the side panels.
11
Lift the front panel up and out.
12
Use pliers to release the spring clamps securing the hose to the tub and drain pump.
13
Pull the old hose free - be prepared for some water to spill.
14
Prepare the new tub-to-pump hose for installation…
15
…by aligning the provided screw clamps on the ends of the hose.
16
Attach one end to the tub and the other end to the drain pump.
17
Tighten the screws to secure the clamps.
18
Reinstall the front panel by aligning the slots in the panel on the side panel mounting clips.
19
Thread the screws to secure.
20
Reposition the support bar and thread the screw.
21
Realign the top panel and lid on the washer and push the panel straight back.
22
Be aware the lid switch wire connecter on the panel needs to be fully connected with the receptacle on the frame.
23
Reinsert the two spring clips to secure the panel.
24
Reposition the rear access panels and rethread the screws.
25
Reinsert the access panel clips.
26
Reposition the lower access panel and secure it with the screws.
27
Plug the power cord back in or restore the power supply…
28
…and your washer/dryer combo should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the tub-to-pump hose on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if the washer is not draining.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Before you replace the tub-to-pump hose in your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a phillips-head screwdriver to unthread the screws securing the lower access panel.
4
Detach the panel and set it aside.
5
Remove the two rear access panel clips
6
Use a quarter-inch socket or nut driver to unthread the screws so you can detach the access panels.
7
Use a short flat-head screwdriver to help detach the spring clips securing the washer’s top panel and lid.
8
Pull the top panel forward then lift up.
9
Use a 5/16th inch socket or nut driver to unthread the screw to release the support bar from the front panel.
10
Next, unthread the screws securing the front panel to the side panels.
11
Lift the front panel up and out.
12
Use pliers to release the spring clamps securing the hose to the tub and drain pump.
13
Pull the old hose free - be prepared for some water to spill.
14
Prepare the new tub-to-pump hose for installation…
15
…by aligning the provided screw clamps on the ends of the hose.
16
Attach one end to the tub and the other end to the drain pump.
17
Tighten the screws to secure the clamps.
18
Reinstall the front panel by aligning the slots in the panel on the side panel mounting clips.
19
Thread the screws to secure.
20
Reposition the support bar and thread the screw.
21
Realign the top panel and lid on the washer and push the panel straight back.
22
Be aware the lid switch wire connecter on the panel needs to be fully connected with the receptacle on the frame.
23
Reinsert the two spring clips to secure the panel.
24
Reposition the rear access panels and rethread the screws.
25
Reinsert the access panel clips.
26
Reposition the lower access panel and secure it with the screws.
27
Plug the power cord back in or restore the power supply…
28
…and your washer/dryer combo should be ready for use.
Applicable Product Model
Parts Needed
Tub-to-Pump Hose
$22.20
Total$0.00
Related Articles & Videos
05:07
Part Replacement
Whirlpool Electric Washer/Dryer Combo Lid Switch Assembly Replacement Part # WP3355458
08:48
Part Replacement
Whirlpool Electric Washer/Dryer Combo Dryer Drive Belt Replacement #661570V
04:26
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Thermal Fuse Replacement #279769
05:56
Part Replacement
Whirlpool Electric Washer/Dryer Combo Water Inlet Valve Replacement #W10919200
03:57
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Replacement #WP3387749
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com