Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Electric Washer/Dryer Combo Lid Hinge Spring Replacement #WP3350152 
Whirlpool Electric Washer/Dryer Combo Lid Hinge Spring Replacement #WP3350152
Skill Level
Total Parts Cost
$78.80Estimated Savings
$112.5004:11
- Description
This video provides step-by-step repair instructions for replacing the lid hinge spring on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if the washer lid is hard to lift.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Before you replace a lid hinge spring in your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a phillips-head screwdriver to unthread the screws securing the lower access panel.
4
Detach the panel and set it aside.
5
Remove the two rear access panel clips
6
Use a quarter-inch socket or nut driver to unthread the screws so you can detach the access panels.
7
Use a short flat-head screwdriver to help detach the spring clips securing the washer’s top panel and lid.
8
Pull the top panel forward then lift up.
9
Set the panel upside-down on a sturdy surface covered with a towel or blanket.
10
Lift the panel up to detach the two spring housings.
11
Now use pliers to squeeze the retaining clip to fully release the old lid hinge spring.
12
Install the new hinge spring…
13
…by aligning both the retaining clip and the spring housing on the hinge.
14
The clip should be positioned in the groove.
15
Lift the panel back up so you can insert the two spring housing pins in their respective brackets.
16
Returning to the appliance, realign the top panel and lid on the washer and push the panel straight back.
17
Be aware the lid switch wire connecter on the panel needs to be fully connected with the receptacle on the frame.
18
Reinsert the two spring clips to secure the panel.
19
Reposition the rear access panels and rethread the screws.
20
Reinsert the access panel clips.
21
Reposition the lower access panel and secure it with the screws.
22
Plug the power cord back in or restore the power supply…
23
…and your washer/dryer combo should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the lid hinge spring on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if the washer lid is hard to lift.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Before you replace a lid hinge spring in your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a phillips-head screwdriver to unthread the screws securing the lower access panel.
4
Detach the panel and set it aside.
5
Remove the two rear access panel clips
6
Use a quarter-inch socket or nut driver to unthread the screws so you can detach the access panels.
7
Use a short flat-head screwdriver to help detach the spring clips securing the washer’s top panel and lid.
8
Pull the top panel forward then lift up.
9
Set the panel upside-down on a sturdy surface covered with a towel or blanket.
10
Lift the panel up to detach the two spring housings.
11
Now use pliers to squeeze the retaining clip to fully release the old lid hinge spring.
12
Install the new hinge spring…
13
…by aligning both the retaining clip and the spring housing on the hinge.
14
The clip should be positioned in the groove.
15
Lift the panel back up so you can insert the two spring housing pins in their respective brackets.
16
Returning to the appliance, realign the top panel and lid on the washer and push the panel straight back.
17
Be aware the lid switch wire connecter on the panel needs to be fully connected with the receptacle on the frame.
18
Reinsert the two spring clips to secure the panel.
19
Reposition the rear access panels and rethread the screws.
20
Reinsert the access panel clips.
21
Reposition the lower access panel and secure it with the screws.
22
Plug the power cord back in or restore the power supply…
23
…and your washer/dryer combo should be ready for use.
Applicable Product Model
Parts Needed
Hinge Spring
$78.80
Total$0.00
Related Articles & Videos
05:07
Part Replacement
Whirlpool Electric Washer/Dryer Combo Lid Switch Assembly Replacement Part # WP3355458
08:48
Part Replacement
Whirlpool Electric Washer/Dryer Combo Dryer Drive Belt Replacement #661570V
04:26
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Thermal Fuse Replacement #279769
05:56
Part Replacement
Whirlpool Electric Washer/Dryer Combo Water Inlet Valve Replacement #W10919200
03:57
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Replacement #WP3387749
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com