Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Electric Washer/Dryer Combo Water Inlet Spout Replacement #WP3360977 
Whirlpool Electric Washer/Dryer Combo Water Inlet Spout Replacement #WP3360977
Skill Level
Total Parts Cost
$46.34Estimated Savings
$112.5004:06
- Description
This video provides step-by-step repair instructions for replacing the water inlet spout on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if it is damaged or missing.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Before you replace the water inlet spout in your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a phillips-head screwdriver to unthread the screws securing the lower access panel.
4
Detach the panel and set it aside.
5
Remove the two rear access panel clips
6
Use a quarter-inch socket or nut driver to unthread the screws so you can detach the access panels.
7
Use a short flat-head screwdriver to help detach the spring clips securing the washer’s top panel and lid.
8
Pull the top panel forward then lift up.
9
If still intact, detach the inlet spout mounting tabs from the bracket.
10
Use pliers to release the spring clamp to detach the hose from the old spout – be prepared for some water to spill.
11
Install the new water inlet spout…
12
…by first attaching the hose and securing it with the spring clamp.
13
Now insert the inlet spout tabs into the bracket until the spout is fully seated.
14
Realign the top panel and lid on the washer and push the panel straight back.
15
Be aware the lid switch wire connecter on the panel needs to be fully connected with the receptacle on the frame.
16
Reinsert the two spring clips to secure the panel.
17
Reposition the rear access panels and rethread the screws.
18
Reinsert the access panel clips.
19
Reposition the lower access panel and secure it with the screws.
20
Plug the power cord back in or restore the power supply…
21
…and your washer/dryer combo should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the water inlet spout on a Whirlpool electric washer/dryer combo (model #WET4027EW0). The most common reason for replacing this part is if it is damaged or missing.
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This replacement video is applicable to the following brands:
Whirlpool, Maytag, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Before you replace the water inlet spout in your washer / dryer combo…
2
…be sure to unplug the power cord or shut off the power supply.
3
Use a phillips-head screwdriver to unthread the screws securing the lower access panel.
4
Detach the panel and set it aside.
5
Remove the two rear access panel clips
6
Use a quarter-inch socket or nut driver to unthread the screws so you can detach the access panels.
7
Use a short flat-head screwdriver to help detach the spring clips securing the washer’s top panel and lid.
8
Pull the top panel forward then lift up.
9
If still intact, detach the inlet spout mounting tabs from the bracket.
10
Use pliers to release the spring clamp to detach the hose from the old spout – be prepared for some water to spill.
11
Install the new water inlet spout…
12
…by first attaching the hose and securing it with the spring clamp.
13
Now insert the inlet spout tabs into the bracket until the spout is fully seated.
14
Realign the top panel and lid on the washer and push the panel straight back.
15
Be aware the lid switch wire connecter on the panel needs to be fully connected with the receptacle on the frame.
16
Reinsert the two spring clips to secure the panel.
17
Reposition the rear access panels and rethread the screws.
18
Reinsert the access panel clips.
19
Reposition the lower access panel and secure it with the screws.
20
Plug the power cord back in or restore the power supply…
21
…and your washer/dryer combo should be ready for use.
Applicable Product Model
Parts Needed
Water Inlet
$46.34
Total$0.00
Related Articles & Videos
05:07
Part Replacement
Whirlpool Electric Washer/Dryer Combo Lid Switch Assembly Replacement Part # WP3355458
08:48
Part Replacement
Whirlpool Electric Washer/Dryer Combo Dryer Drive Belt Replacement #661570V
04:26
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Thermal Fuse Replacement #279769
05:56
Part Replacement
Whirlpool Electric Washer/Dryer Combo Water Inlet Valve Replacement #W10919200
03:57
Part Replacement
Whirlpool Electric Washer/Dryer Combo Heating Element Replacement #WP3387749
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com