Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Gas Range Broil Burner Tube Replacement #W11233678 
Whirlpool Gas Range Broil Burner Tube Replacement #W11233678
Skill Level
Total Parts Cost
$56.33Estimated Savings
$112.5003:08
- Description
This video provides step-by-step repair instructions for replacing the broil burner tube on a Whirlpool gas range. The most common reason for replacing this part is if the broiler will not light.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step By Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Broil Burner Tube Replacement
3
Tools needed: Phillips-head screwdriver or a number two square drive bit,
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Fire Hazard
7
Shut off the gas supply as well.
8
Fully open the oven door and rotate both door hinge locks back.
9
Heavy
10
Partially close the door, then lift and pull the door toward you to remove.
11
With the handle side down, set the door on a blanket or towel.
12
Remove the oven racks.
13
Use a Phillips-head screwdriver or a number two square drive bit to unthread the mounting screw in the front.
14
Sharp
15
Remove the shield.
16
Detach the burner tube and disconnect the spark electrode wire to fully remove the old burner tube ? be careful not to let the electrode wire slip behind the rear panel.
17
Before you install the new broil burner tube, confirm that the air shutter is opened the same amount as the old shutter.
18
Now transfer the spark electrode from the old tube to the new one.
19
Thread the screws to hold it in place.
20
Returning to the oven, connect the wire to the spark electrode.
21
Position the burner tube over the orifice.
22
Realign the shield, then fully position the assembly and thread the front mounting screw.
23
Replace the oven racks.
24
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
25
Lower the door to its fully open position, then rotate the hinge locks forward.
26
Turn the gas supply back on, plug the power cord back in or restore the power supply and the gas range should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the broil burner tube on a Whirlpool gas range. The most common reason for replacing this part is if the broiler will not light.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step-By-Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Broil Burner Tube Replacement
3
Tools needed: Phillips-head screwdriver or a number two square drive bit,
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Fire Hazard
7
Shut off the gas supply as well.
8
Fully open the oven door and rotate both door hinge locks back.
9
Heavy
10
Partially close the door, then lift and pull the door toward you to remove.
11
With the handle side down, set the door on a blanket or towel.
12
Remove the oven racks.
13
Use a Phillips-head screwdriver or a number two square drive bit to unthread the mounting screw in the front.
14
Sharp
15
Remove the shield.
16
Detach the burner tube and disconnect the spark electrode wire to fully remove the old burner tube ? be careful not to let the electrode wire slip behind the rear panel.
17
Before you install the new broil burner tube, confirm that the air shutter is opened the same amount as the old shutter.
18
Now transfer the spark electrode from the old tube to the new one.
19
Thread the screws to hold it in place.
20
Returning to the oven, connect the wire to the spark electrode.
21
Position the burner tube over the orifice.
22
Realign the shield, then fully position the assembly and thread the front mounting screw.
23
Replace the oven racks.
24
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
25
Lower the door to its fully open position, then rotate the hinge locks forward.
26
Turn the gas supply back on, plug the power cord back in or restore the power supply and the gas range should be ready for use.
Applicable Product Model
Related Articles & Videos
03:22
Part Replacement
KitchenAid Convection Gas Range Broil Burner Tube Replacement #W11233678
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com