Video & Articles: Appliance & Equipment RepairWhirlpool Barracuda Refrigerator Run Capacitor Replacement WPW10350564

Whirlpool Barracuda Refrigerator Run Capacitor Replacement WPW10350564

02:34
This video provides step-by-step repair instructions for replacing the run capacitor on a Whirlpool Barracuda refrigerator (Model WRS325FDAM04). The most common reason for replacing this part is if the refrigerator will not start.

All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore

Step By Step Instructions

1
Before you replace the run capacitor in your refrigerator unplug the power cord
2
Shut off the water supply.
3
Use a wrench to help unthread the nut to release the water supply line from the inlet valve – be prepared for some water to spill.
4
Use a quarter-inch socket or nut driver to remove the screws securing the access panel.
5
Pull the panel out and remove the power cord retainer from the panel.
6
Disconnect the inlet valve wire harness and move the panel out of the way.
7
Unhook the retaining wire securing the start relay assembly to the compressor.
8
You can now pull off the old run capacitor from the relay.
9
Install the new run capacitor by positioning it on the start relay.
10
Replace the retaining wire to secure the assembly.
11
Position the access panel and connect the wire harness to the terminals on the inlet valve.
12
Attach the power cord retainer to the panel then fully reposition the panel.
13
Replace the screws to secure it.
14
Remember to secure the two water lines with the retainers.
15
Secure the water supply line to the valve with the nut.
16
With the repair completed turn the water supply back on
17
Plug the power cord back in and you refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the run capacitor on a Whirlpool Barracuda refrigerator (Model WRS325FDAM04). The most common reason for replacing this part is if the refrigerator will not start.

All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
Step-By-Step Instructions
1
Before you replace the run capacitor in your refrigerator unplug the power cord
2
Shut off the water supply.
3
Use a wrench to help unthread the nut to release the water supply line from the inlet valve – be prepared for some water to spill.
4
Use a quarter-inch socket or nut driver to remove the screws securing the access panel.
5
Pull the panel out and remove the power cord retainer from the panel.
6
Disconnect the inlet valve wire harness and move the panel out of the way.
7
Unhook the retaining wire securing the start relay assembly to the compressor.
8
You can now pull off the old run capacitor from the relay.
9
Install the new run capacitor by positioning it on the start relay.
10
Replace the retaining wire to secure the assembly.
11
Position the access panel and connect the wire harness to the terminals on the inlet valve.
12
Attach the power cord retainer to the panel then fully reposition the panel.
13
Replace the screws to secure it.
14
Remember to secure the two water lines with the retainers.
15
Secure the water supply line to the valve with the nut.
16
With the repair completed turn the water supply back on
17
Plug the power cord back in and you refrigerator should be ready for use.

Applicable Product Model

icons/refrigerator
Brand
Product Type
Model
Subtype
Cooling System
Icemaking System
Dispensing System
Product Diagram & Manuals
Parts Needed
Total$0.00

Related Articles & Videos

03:36
Part Replacement
Whirlpool Sidekick Refrigerator Run Capacitor Replacement WPW10350564
02:58
Part Replacement
Whirlpool Refrigerator Run Capacitor Replacement #W10350564
03:51
Part Replacement
Whirlpool Sidekick Freezer Run Capacitor Replacement WPW10350564
04:33
Part Replacement
Whirlpool Barracuda Refrigerator Water Filter Housing Replacement W10862461
01:14
Part Replacement
Whirlpool Barracuda Refrigerator Top Liner LED Replacement WPW10515058