Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairEcho Hedge Trimmer Rear Handle Replacement #C410000920
Echo Hedge Trimmer Rear Handle Replacement #C410000920
Skill Level
Total Parts Cost
$21.72Estimated Savings
$112.5004:09
- Description
This video provides step-by-step repair instructions for replacing the rear handle on an Echo hedge trimmer. The most common reason for replacing the handle is if it is broken.
All of the information in this handle replacement video is applicable to the following brands: Echo
Tools used: 14mm wrench, flat head screwdriver, 8mm socket, T-27 Torx bit, 10mm socket
All of the information in this handle replacement video is applicable to the following brands: Echo
Tools used: 14mm wrench, flat head screwdriver, 8mm socket, T-27 Torx bit, 10mm socket
Step By Step Instructions
1
Before you replace the rear handle on your hedge trimmer make sure the engine has cooled.
2
Next, you should remove the wire and boot from the spark plug to prevent the engine from accidentally starting.
3
Use a 14mm wrench to unthread the nut securing the on-off switch.
4
Now use a flat-head screwdriver to depress the retaining tab to release the handle cover.
5
Fully remove the cover and detach the throttle control lock lever.
6
Next, remove the throttle control lever and spring.
7
You can use the screwdriver to help detach the throttle cable from the handle assembly then remove the wire and cable conduit.
8
Use an 8mm socket and a t-27 torx bit to remove the nuts and bolts securing the handle.
9
Slide the old handle off.
10
Install the new rear handle by sliding it onto the gear case.
11
Replace the nuts and bolts to secure.
12
Feed the wire and cable conduit into the handle and secure the cable in the retaining slot.
13
You can provide more slack for the cable by using a 10mm wrench to loosen the throttle cable locking nut on the carburetor and pushing the cable up.
14
Insert the end of the throttle cable into the throttle control lever and secure it in the slot.
15
Now reposition the spring on the control lever then align the spring as you snap the lever into place.
16
If applicable, reposition the opposite end of the throttle cable in the carburetor bracket and tighten the locking nut.
17
Now snap the lock lever into place.
18
Align the eyelet terminal over the on-off switch position the handle cover then insert the switch through the hole in the cover and snap the cover into place.
19
Thread the nut to secure the switch.
20
With the repair completed reattach the wire and boot to the spark plug and your hedge trimmer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the rear handle on an Echo hedge trimmer. The most common reason for replacing the handle is if it is broken.
All of the information in this handle replacement video is applicable to the following brands: Echo
Tools used: 14mm wrench, flat head screwdriver, 8mm socket, T-27 Torx bit, 10mm socket
All of the information in this handle replacement video is applicable to the following brands: Echo
Tools used: 14mm wrench, flat head screwdriver, 8mm socket, T-27 Torx bit, 10mm socket
Step-By-Step Instructions
1
Before you replace the rear handle on your hedge trimmer make sure the engine has cooled.
2
Next, you should remove the wire and boot from the spark plug to prevent the engine from accidentally starting.
3
Use a 14mm wrench to unthread the nut securing the on-off switch.
4
Now use a flat-head screwdriver to depress the retaining tab to release the handle cover.
5
Fully remove the cover and detach the throttle control lock lever.
6
Next, remove the throttle control lever and spring.
7
You can use the screwdriver to help detach the throttle cable from the handle assembly then remove the wire and cable conduit.
8
Use an 8mm socket and a t-27 torx bit to remove the nuts and bolts securing the handle.
9
Slide the old handle off.
10
Install the new rear handle by sliding it onto the gear case.
11
Replace the nuts and bolts to secure.
12
Feed the wire and cable conduit into the handle and secure the cable in the retaining slot.
13
You can provide more slack for the cable by using a 10mm wrench to loosen the throttle cable locking nut on the carburetor and pushing the cable up.
14
Insert the end of the throttle cable into the throttle control lever and secure it in the slot.
15
Now reposition the spring on the control lever then align the spring as you snap the lever into place.
16
If applicable, reposition the opposite end of the throttle cable in the carburetor bracket and tighten the locking nut.
17
Now snap the lock lever into place.
18
Align the eyelet terminal over the on-off switch position the handle cover then insert the switch through the hole in the cover and snap the cover into place.
19
Thread the nut to secure the switch.
20
With the repair completed reattach the wire and boot to the spark plug and your hedge trimmer should be ready for use.
Applicable Product Model
Parts Needed
Handle
$21.72
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com