Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Front Load Washer Inner Door Panel #WPW10208275
Whirlpool Front Load Washer Inner Door Panel #WPW10208275
Skill Level
Total Parts Cost
$144.68Estimated Savings
$112.5004:50
- Description
This video provides step-by-step repair instructions for replacing the inner door panel on a Whirlpool washer. The most common reason for replacing the inner door panel is if it is damaged.
This inner door panel replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, T-15 Torx bit, T-20 Torx bit, flat-head screwdriver
This inner door panel replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, T-15 Torx bit, T-20 Torx bit, flat-head screwdriver
Step By Step Instructions
1
Before you replace the inner door panel on your washer be sure to unplug the power cord.
2
Open the washer door and use a t-25 torx bit to unthread the screws securing the door hinge.
3
With the screws unthreaded, lift the door up to detach it from the front panel.
4
Using a t-15 torx bit, unthread the screws holding the inner and outer door panels together.
5
Separate the panels.
6
Use a t-20 torx bit to unthread the screws securing the door glass retaining brackets.
7
Remove the door glass.
8
Using the t-15 torx bit, unthread the screws securing the door hinge cover plate.
9
Lift off the plate and remove the door hinge.
10
Use a flat-head screwdriver to pry off the tension bracket.
11
Remove the screws to release the door strike as well.
12
You’re now ready to prepare the new inner door panel for installation.
13
Position the door strike and snap it into place.
14
Thread the screws to secure but don’t tighten them – the strike should be allowed to slide back and forth.
15
Snap the tension bracket into place.
16
Before you install the door hinge, makes sure all four hinge bearings are in place.
17
Now align the hinge on the inner panel.
18
Position the hinge cover plate and secure it with the screws.
19
Position the door glass then realign the retaining brackets and replace the screws.
20
Align the inner and outer door panels.
21
Rethread the screws to secure.
22
Insert the hinge tabs into the front panel slots.
23
Rethread the screws to secure.
24
With the repair completed. plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the inner door panel on a Whirlpool washer. The most common reason for replacing the inner door panel is if it is damaged.
This inner door panel replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, T-15 Torx bit, T-20 Torx bit, flat-head screwdriver
This inner door panel replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, T-15 Torx bit, T-20 Torx bit, flat-head screwdriver
Step-By-Step Instructions
1
Before you replace the inner door panel on your washer be sure to unplug the power cord.
2
Open the washer door and use a t-25 torx bit to unthread the screws securing the door hinge.
3
With the screws unthreaded, lift the door up to detach it from the front panel.
4
Using a t-15 torx bit, unthread the screws holding the inner and outer door panels together.
5
Separate the panels.
6
Use a t-20 torx bit to unthread the screws securing the door glass retaining brackets.
7
Remove the door glass.
8
Using the t-15 torx bit, unthread the screws securing the door hinge cover plate.
9
Lift off the plate and remove the door hinge.
10
Use a flat-head screwdriver to pry off the tension bracket.
11
Remove the screws to release the door strike as well.
12
You’re now ready to prepare the new inner door panel for installation.
13
Position the door strike and snap it into place.
14
Thread the screws to secure but don’t tighten them – the strike should be allowed to slide back and forth.
15
Snap the tension bracket into place.
16
Before you install the door hinge, makes sure all four hinge bearings are in place.
17
Now align the hinge on the inner panel.
18
Position the hinge cover plate and secure it with the screws.
19
Position the door glass then realign the retaining brackets and replace the screws.
20
Align the inner and outer door panels.
21
Rethread the screws to secure.
22
Insert the hinge tabs into the front panel slots.
23
Rethread the screws to secure.
24
With the repair completed. plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com